Description: Adopting advanced digital signal processing technology, Compounding of high precision passive infrared detector and logical digital circuit design, feature intelligent power save, auto- temperature compensation, low battery alarm and so on. It emits wireless digital signal to start the control panel for alarm through detecting human being body infrared heat. Nice looking, Reliable and fine quality. It can be compatible with many other control panel. Function: 1. Tamper switch: it will send alarm signal if cover is disassembled 2. Preset coding with the control panel: Switch the protection zone to “ON”, press the tamper switch and send wireless signal, the control panel sounds, it means that coding is completed matched.(refer to the coding program of control panel operation instruction and relative detector) 3. Low battery alarm: when battery is low voltage, the human being body moving, LED flashes five times. In static environment ,it is not activated. 4. Coding address: preset by manufacture or by user. 5.Protected time choosing: 3 seconds or 30 seconds, it is preset by playing pins. 6. Compatible with many control panel. Specification: Power supply: 9VDC Li-ion & manganese battery 500mAh Working current: static 30µA; alarm 16 mA Wireless parameter: frequency 315MHz or 433MHz, Transmitting distance 150 m (wide area without interfere) Detecting range: high 2.4m from ground, covered diameter:7.3m, high 4.5m, covered diameter: 9mWorking condition: working temperature: -10ºC~55ºC Product size: Φ96*25mm Installation: 1, Installing guide Open the cover, connect the battery, than the detector starts to work. Press tamper switch to transmit the signal to match coding of the control panel Close the cover, when installing it, please learn the following diagram. When the power is on, the LED flashes for about two seconds, the detector will continues to delay for about three seconds or thirty seconds (it depends on protecting time choosing),than it enters the activate situation. If intruder enter protection area. The detector immediately sends out wireless alarm signal. 2. Usage Walk test: to set the protecting time choosing to 3 seconds by playing pin, simulated as intruder go into the protection area, the LED flashes for about 2 seconds, the detector sends out the wireless signal, meanwhile, the control panel should receive the signal. After walk test, it tested well, please set the protecting time choosing to 30 seconds so as to start to work. Note: When setting the protecting time, please shut off battery power and press tamper switch once. Caution: Install the detector to the proper place where intruder must enter. Do not face the detector to any area where window, lamp-house, heat thing and so on. It is used for indoor,not for outdoor .When installing, do not drop down or hit the detector so to avoid the internal infrared sensor. Do not touch the sensor lens so to avoid the detecting distance and sensitivity. Have termly walk test

Specification: Working voltage: 12V battery Frequency: 315MHz/433MHz Working temperature: -15 ℃ -55 ℃ Detecting rang: max 9meter (when presetting to identify direction);max 12meter without presetting to identifying direction) Static current: 30HA Alarm current: 20mA Installation: 2 -2.4m (above the ground) Anti-electromagnetism : >30 v/m Anti-white-light : >6500 LUX Size: 110×70×40mm N.W.: 130g

especially inner balcony to substitute metal structure. It gives you beautiful feeling.It will alarm at once and dial the pre-set alarm numbers. 1, The emitting bundle is shutoff by the object diameter of 20cm 2, The working elements as bellows: Several unvisible defense bundles from the remitters forms protection network. The buzzer of the receiver will hoot once any bundle is shut off for over 40ms and then the alarm host will send out the radio alarm. The remitting will think it is normal and will not send out the alarm signal to alarm host when a small animal such as bird, dove jump the protection area because they only shut off one infrared remitting bundle. Features: 1, Dormant defense and protection baluster makes the burglar found in no any sense. 2, Complete defense ability: It can detect any activation of the burglar 3, Good interfereproof characteristics: It wound not occur wrong report for the insect and other mall animal. 4, Strict anti-destroy ability: It will output the alarm signal once the power or cable are cut. Specification: 1, Power voltage: +12VDC 2,Current: 50mA remitting, 60mA receiving, 45mA alarm 3,Protection area: 30m inner, 10-25m outside. 4,Maximum remitting bundle distance: 36m 5,Remitting bundle numbers: 2 or more 6,The width of the remitting bundle: 100mm 7,Detecting type: Single bundle, complete shutoff trigger 8,Trigger time: 40ms 9,Workign temperature: -10 ~ +50℃, relative humidity: ≤95% 10,Alarm output: Radio remitting output. 11, Alarm type: Locale Alarm and dial the telephone automatically and send out the DTMF and broadcasting record 12, The remitter weight exclusive battery: 500g 13, The receiver weight exclusive: 500g